VVDI Prog programmer is good programmer for BMW car models,if you bought VVDI2 BMW,VVDI Prog will be a perfect tool to work with VVDI2 BMW,especially for BMW CAS4,as well as EWS and other CAS.Here we will show VVDI Prog works on BMW CAS2 BMW CAS3+.
1.VVDI Prog work with BMW CAS2
BMW CAS2 Type
VVDI PROG CAS2 Diagram connection
VVDI Prog Programmer Read BMW CAS3+ OL15Y
BMW CAS3+ TYPE
Choose BMW CAS3+ type
Connection Diagram
Soldering and connecting
www.xhorsevvdi.com all rights reserved, Original Article url:VVDI Prog Programmer Works on BMW CAS2 BMW CAS3+
0 Comments
Here is 2016 Actia MultiDiag software installation guide step by step for you! Check below and start!
Step 1
Open Actia Multi-Diag 2016 software “I 2016_36.05 (E:) “.
Copy SN 033918.txt to desktop and open Actia Multi-Diag 2016 setup.exe.
You will see Multi-Diag Office InstallShield Wizard.
Click “Next”, “I accept…” then “Next”.
Copy the SN “033918” from txt file and click “Next”.
Select the setup type: USA.
Then choose “Profile ACTIA (Standard)” option.
Wait it complete and you will see the Multi-Diag shortcut on desktop.
Choose the “restart computer” option and click “Finish”.
Step 2
After that it will automatically pop up a Found New Hardware Wizard for Pass-Thru XS USB Driver.
Choose “Install the software automatically (Recommended)” option and click “Next” then “Finish”.
Now you can find the Pass-Thru XS USB Driver already exist.
Step 3
Then you can see a Found New Hardware Wizard for USB Pass-Thru Driver (Multi-instance).
Choose “Install from a list of specific location” option and click “Next”.
Check the box “Include this location in the search” then choose C: disk→ ACTIA→ Drivers VCI→ PT1G.
Click “Next” then “Finish”.
www.obd2france.com all rights reserved, Original Article url:How to install I-2016 Actia Multi-Diag Access J2534 Pass-Thru?
VVDI MB BGA Tool Benz key programmer which is designed by Xhorse,except xhorse original tools,we also recommend original YANHUA Mercedes Benz 315MHZ/433MHZ Key to work with VVDI MB Tool.
Top 5 reasons to get YH Mercedes Benz 315MHZ/433MHZ Key:
1. Applicable List: 705 Moto(1997-2000) NEC(2001-2005) NEC(2006-2010) BGA(after 2011)
2. Programmed by:All kinds of MB key programmer such as Digimaster-III ,CKM100, VVDI MB TOOL, AK500 , MBE MB-KEY OBD2, NEC-57 MB-PRO,Etc.
3. Frequency: 315MHZ/433MHZ
4. Advantage: Support repeated infrared reading and writing. Steady quality same as original one.
5.This key is reusable,and it can write again directly
YH Benz Key PCB Board Display:
www.xhorsevvdi.com all rights reserved, Original Article url:YH Mercedes Benz 315MHZ/433MHZ Key Support Work with VVDI MB Tool
VVDI2 and VVDI PROG both of them are xhorse original tools,VVDI PROG can read BMW ISN and eeprom.etc,vvdi2 key programmer is univeral tool.Here XhorseVVDI.com will take Audi A6l 2.4 all key lost as a example to the detailed steps how to use Xhorse VVDI2 and VVDI Prog to make key.
1.Open Engine cover, find out the Engine position, remove the engine ECU.
2.Read 95320 chip.Use VVDI prog to read 95320 chip,please remove the chip and put it on the VVDI Programmer.
Start VVDI Prog software,choose the chip type,read out the data,and save it.
3.Remove the 95320 chip,solder chip back on engine.
4.Start VVDI2 software and choose Audi car brand.
5.Click speical function,then select” EEPROM data processing tool”
6.Calculate the CS Code.
Choose ECU Simons PPDIX – Reset component protection data.Open VVDI2 and click Audi option,and Load the data that read out by VVDI Prog.Then click open.
Record the CS code.
7.Calculate PIN Code
Select ECU Simons PPDIX – Security Access Code,load again the file,and record the PIN CODE.
8.Start VVDI2 software, click Learning Key- Audi A6/Q7.
Input the CS and PIN code ,then the button Learning Key and Generate dealer key will be OK to click.Put OEM chip and 8E chip into VVDI2 key programmer.Then click generate dealer key.
9.Learning key.
Disconnect the short insurance line and connect back.
Take out the key from VVDI2 and put it into ignition data coil.Click Learning Key .Open and close car door, turn on ignition, press down brake.
10.Read out EZS-KESSY(J518)EEPROM.
Click ok, select Chip type 9S1201128, read EZS-KESSY(J518)EEPROM is to generate OEM remote control.Save EZS-KESSY(J518)EEPROM.Generate OEM remote control.
Please confirm that remote controller is on the coil of VVDI2.
11.Test
www.xhorsevvdi.com all rights reserved, Original Article url:How to use Xhorse VVDI2 and VVDI Prog to make Audi A6l 2.4 Key
This is how to use JDiag Elite Pro programming tool for Mercedes W211online
SCN coding with DAS.
Model:
Mercedes Benz W211.056
Module for coding:
W211.056 Transmission
Device can be used:
SD connect c4 multiplexer
How to do W211SCN coding online:
Check connection of the car and diagnostic tool
Run Jdiag Mercedes software DAS
Transmission
Confirmed VIN stored in control module and go on
Warning:
-connect battery charger
-make sure that the diagnostic plug is properly seated in the diagnostic socket
-the diagnostic connector must remain plugged in to the vehicle
-switch off all electrical consumers
-if possible, do not perform any procedures on the vehicle during control unit programming
Daimler login
Continue
Data is being determined
Important note:
-secure vehicle to prevent it rolling away and apply parking brake
-the teach-in process for the selection range sensor may only be performed after the shift rod has been properly set
You will guided through the following steps:
-teach-in selection sensor range in selector lever position P
-teach-in selection sensor range in selector lever position R
-teach-in selection sensor range in selector lever position N
-teach-in selection sensor range in selector lever position D
Initial startup was fully completed
Result:
Successful!
Perfect scn coding online for W211.056 Transmission with Device JDiag elite pro II
ound-color: white; color: #333333; font-family: Arial, Helvetica, sans-serif; font-size: 14px; font-style: normal; font-variant: normal; font-weight: normal; letter-spacing: normal; line-height: 25.2px; margin: 0px 0px 10px; orphans: auto; text-align: start; text-indent: 0px; text-transform: none; white-space: normal; widows: 1; word-spacing: 0px;"> Choose “Install from a list of specific location” option and click “Next”.
Check the box “Include this location in the search” then choose C: disk→ ACTIA→ Drivers VCI→ PT1G.
Click “Next” then “Finish”.
www.obd2france.com all rights reserved, Original Article url:How to install I-2016 Actia Multi-Diag Access J2534 Pass-Thru?
VVDI MB BGA Tool Programmer is benz professional key programmer,and it can support to do key reading and writing,EIS tools,password calculation,key file preparing,ESL tools,ECU/Gearbox renew and many special functions.And here we will share VVDI Benz read W203 Password via IR mode.
1.Start VVDI MB Tool sotware,EIS Tools and choose IR Mode,then choose W203.
2.Click Read EIS data and password.
3.Read password via IR will take about 1-4 minutes.Click Yes.
4.Read password successfully,then click "Save EIS Data".
5.Click "Prepare key file"in the vvdi mb software main menu.Click "Load EIS File".
6.It is V051,tick off v041,v011,and click "Prepare Key File".
7.Click read/write key,and then click Identification key.
8.Load Key file.Then click "Write",waiting for the writing process.
Xhorse ELV Emulator for Benz 204 207 212 Work with VVDI MB BGA Tool (Support Ship From US/UK),and here is test result.
1.Success used ELV emulator/simulator in W204:
1). EIS: read data by OBD from EIS/EZS …… OK
2). EIS: get erase password ……. OK
3). password calc.: get key password through calc. process and 1 token used ……OK
4). EIS: save all data of EIS ……. OK
5). EIS: renew EIS/EZS through IR ……. OK
6). EIS: load back saved data …….. OK
7). EIS: write data to EIS/EZS …… OK
8). EIS: personalize ELV emulator in EIS/EZS unit – success….. OK
9). EIS and ELV now working and car start
10). ELV emulator/simulator from Xhorse have sound (unlock and lock job) almost as original ELV
After all this steps still missed VIN in EIS/EZS, and fault in ESP because not see VIN from EIS,
then finished with XENTRY and write VIN to EIS/EZS in EIS/EZS unit finished…. OK
erase all faults ….. OK
I renew W204 ELV Xhorse emulator only through 2x click…no need any data or passwords.
Original metalic W204 ELS/ELV unit renew is different process and steps…there you need erase passwords to have.
I unlock NEC from 3x blocked W204 ELV, i think it take 3-5 attempts, each delay 100-1000 times cca, don’t know exactly now…
only try….failed…try….failed….try….success.
2.The process to renew EIS for ESL/ELV personalizes described in VVDI MB BGA manual:
ESL Tools
Support read ESL data via OBD (K-Line) …… tested OK
Support renew ESL, make 2nd hand ESL to new one (online) ……. tested OK ( online get only erase pass ) Support replace ESL, you can write original ESL or EIS data to new ESL …… tested OK ( but key password is needed to have too ) Support write new VIN …… tested OK ( i write there 999999 and OK ) Support clear TP Support auto personalized ESL, no need renew EIS ……not tested yet Support check ESL damage status …… tested OK Support repair W204 ESL NEC chip(fatal error: 0xAA) and Motorola ESL chip …… tested OK ( NEC chip only yet ) Support renew VVDI-MB W204 emulator …… tested OK and on next page is:
Special Instructions (2016.05.29)
The newest cars after 2015 with FBS4 EIS don’t support read data and password, we are researching it
Renew EIS and renew ESL require erase password. We are building a new server for erase password. It will support all erase password after new server finished
Auto personalized ESL: Now only support auto personalized ESL with key password all 00,
we will support all the passwords in future (You can use “Personalize W204 ESL” instead before we publish new version).
In ESL window, you can input crypto password for auto personalize (no need renew EIS).
Crypto password need calculate with other tools
VVDI2 BMW and BMW MULTI TOOL,both of them are xhorse professional key programmer.As we all know,VVDI2 Covers All the Functions of VVDI, VVDI 5th IMMO Adapter, BMW Multi Tool, CAS Plus, CAS4 Adapter and so on.For VVDI2 BMW,it covers BMW MULTI Tool all functions.
1.VVDI2 BMW VS BMW Multi Tool Comparison
VVDI2 BMW key programmer covers all function of BMW MULTI Tool.
BMW MULTI TOOL newest version is V7.7.
VVDI2 BMW will have firmware update in future,but BMW MULTI TOOL will have limit.Considering the Firmware update,you can check BMW Multi Tool.BMW Multi Tool is more economical.
2.VVDI2 BMW VS BMW Multi Tool Support List
Many customs want to know whether VVDI2 BMW can do all bmw cars by OBD way,the answer is no,it is like BMW MULTI Tool car list pic,it can supprt CAS1-CAS4.VVDI2 advantage is VVDI2 BWM can support CAS4+ if pay for the CAS4+ authorization,but BMW MULTI TOOL can not.
Here is support list,it has three ways to do keys,OBD2,EEPROM,CAS Plug:
About EEPROM dump way,it needs to remove the dashboard,use VVDI prog to read the data,then use VVDI2 BMW to make new keys.
www.xhorsevvdi.com all rights reserved, Original Article url:Xhorse VVDI2 BMW VS BMW Multi Tool Key Programmer
F100 Key Programmer is known as a Ford key programmer, but actually it’s OBD program keys and correct mileage to Ford, Jaguar, Land Rover and Mazda. So, obdstar f100 is not only an auto key programmer but also an odometer correction tool.
obdstar f100 for sale:
obdstar f100 price: €126
obdstar f100 update:
Original OBDSTAR F100 can be updated online via http://en.obdstar.com/
Free update for 1 year; and it will cost 80USD/year after 1 year
obdstar f100 instructions:
obdstar f100 car list:
obdstar f100 review:
Here share with you EASY steps to change Yamaha YZF R1 2001 mileage by Digiprog iii V4.94. Easy to do even for DIY odometer correction!
Step 1.
Take apart the EEPROM chip Yamaha YZF-R1 93C46.
You can take a close look at as below:
In this case, you need the ST04 cable to connect 93C46 EEPROM chip with Digiprog iii.
Fit the chip with ST04 cable clip properly like this:
Connect ST04 cable with Digiprog iii and connect device to power supply.
Step 2
Device will power on. You will see an information message, click OK.
Input your device password to enter the main menu.
Go to “MOTORCYCLE” section
Scroll down to select “YAMAHA”, “YZF R1” then “C46 (2001)”.
It will show “93CS46 PLUG 1”, click OK to continue.
Step 3
You can see the old odometer value as 27584KM.
And just enter a new value like 40000KM, click OK and confirm it again.
Now you change Yamaha R1 mileage successfully using Digiprog iii Digiprog 3 odometer programmer!
www.obd2france.com all rights reserved, Original Article url:Digiprog 3 V4.94 change Yamaha YZF R1 2001 mileage EASY steps
|
obd2diy.fr:
obd2diy.fr s'applique spécialement à fournir d'appareil diagnostic auto - OBD2 Français Valise Diagnostique. Nous offrons des produits de haute qualité, le meilleur service et le prix le plus compétitif 存档
October 2019
类别 |